Read pages 11-20 text version. Power/Automatic Tools(5) Sure Seal. Chooseappropriatecrimp,insertion,andextractiontoolingon page17. SureSeal CrossSection HowtoSelect Sure-Seal. 225-0093-000 SS-T-Tool DRK152 225-0093-000 070235-0001 SS-CS10. Buy SURE SEAL SSI-T-TOOL online at Newark element14. Buy your SSI-T-TOOL from an authorized SURE SEAL distributor. 27 SURE-SEAL www.ittcannon.com Dimensions shown in mm Specifications and dimensions subject to change Connector fully equipped 20 15 10 5 1 I (A) ( Sure-Seal Applications Features Wet, humid, or dirty environments requir-. An insertion tool is required to insert contacts into the connector. These tools are heavy duty production hand tools. A holding block should also. SURE-SEAL www.ittcannon.com Dimensions shown in mm Specifications and dimensions subject to change Hand Crimp Tool M22520-1-01 (Part Number: 995-0001-585) for machined contacts 330-8672-003 SS10 CT120090-M4 0,75-1,5 6,5 +0,3. Buy Sure Seal Series, Insertion Tool for Pin Contacts 121086-3025 or other Insertion Tools online from RS for next day delivery on your order plus great service and a great price from the largest electronics components. ITT Cannon Sure Seal Insertion Tool. Write Your Own Review You're reviewing: Cannon Sure Seal Insertion Tool, Package of 1 *Nickname *. Items of most general interest to users and designers are listed below. With its current capability and large size, Power Sure- Seal. Tests include immersion in 3 feet depth in water solution containing 5% salt. Contact Tensile. Strength – Crimp. The minimum tensile load required to separate the wire from the contact, either by pulling the wire out of the crimp joint or breaking the wire within the crimp joint, shall not be less than the applicable limits as specified. Wire breakage, or contact damage not due to crimping, at less than tensile loads shall not constitute failure. Crimp Tensile Strength, Pounds Minimum. Without Insulation Support Contacts. With Insulation Support Contacts. Properly assembled and mated connectors shall be tested in accordance with MIL- STD- 2. Method 3. 02, except a potential of 5. The resistance shall be measured between adjacent parts of contacts (or contacts to ground for SS- 1) and shall not be less than 1. M. If the specimen has been immersed in fluid in the preceding test, it shall be placed wet on a conducting surface and insulation resistance measured within 5 minutes between each contact and also between each contact and the conducting surface (except for SS- 1 to be measured contact to ground while immersed). Dielectric Withstanding Voltage. Assembled and mated connectors shall show no evidence of breakdown between adjacent contacts (or contact to ground for SS- 1) when tested in accordance with MIL- STD- 2. Method 3. 01, and a test voltage of 1. Test current to be 1 amp, and MIL- STD- 2. Method 3. 07. Mated connectors properly mounted shall be subjected to the shock test in accordance with MIL- STD- 2. Method 2. 13. B, CONDITION B. The shock test shall be repeated three (3) times in each of X, Y & Z axis. Suitable means shall be employed to monitor the current flow. Current discontinuity of 1 microsecond or more, disengagement of the mated connectors, evidence of cracking, breaking or loosening of parts shall be cause for rejection. Properly assembled and mated connectors shall be mounted to the vibration table, with the wire leads strapped to a vibrating member approximately 3 inches from each end of the connector body and vibrated with a peak- to- peak amplitude of . Hz, and a . The vibration shall be swept up and down for a total of 3. Six (6) hours at 1. Electrical continuity shall be continually monitored. Breaks in continuity longer than one microsecond shall be cause for rejection. The connectors shall be subjected to 2. There shall be no evidence of damage to the contacts, the contact plating, the insulators or sealing rings, which would be detrimental to connector function. With the connector plug or receptacle held firmly, an axial dead weight of 7. Plugs and receptacles to be tested separately. Each wired receptacle and plug shall be subjected to 5 cycles of contact insertion and extraction in the same cavity using the approved tools. Plug and receptacle are to be tested separately. After the 5 cycles of insertion and extraction, each plug and receptacle in turn will be subjected to the contact retention test of 6 lbs. The rate of loading shall be one inch per minute. The sample shall fall within the limits specified as follows: Connector Size. Unmating Force (lbs) Max. Unmating Force (lbs) Min. SS- 1. 12. 6SS- 2. SS- 3. 18. 8SS- 4. SS- 5/7. 30. 10. SS- 8/1. Solvent Resistance. Wired and mated connectors shall be subjected to the applicable fluids for the length of time specified. Following the test the connectors shall be immersed to a depth of 3 feet in salt water for 2. At the completion of the salt water immersion test and while still immersed insulation resistance shall be measured. Failure to meet the insulation resistance requirements shall be cause for rejection. Gasoline Splash. 1 second dip - 3 minute air dry for 8. Diesel Fuel Splash. Automotive Lubricating Oil. Immersed in S. A. E. 3. 0 weight lubricating oil for 1 hour. Antifreeze. Immersed at 1. Brake Fluid Immersed at room ambient temperature for 2. Brake Fluid. Immersed at room ambient temperature for 2. Automatic Transmission Fluid. Immersed at 1. 20. The duration of the test shall be 7 days. Outdoor exposure to be conducted per ASTM D- 1. The connector shall show no cracking or other degradation which would result in loss of sealing integrity. High Temperature. Long- Term. Wired mated connectors shall be tested in accordance with MIL- STD- 2. Method 1. 08. A, Test Condition D at 1. Following the test, they shall be subjected to 3 feet salt water immersion for 2. While immersed, insulation resistance shall be determined. Failure to meet the insulation resistance requirements shall be cause for rejection. Sure Seal Connections has recently completed testing of the Sure Seal PVC Nitrile material (SM 3. UV resistance. The material was tested in accordance with ASTM G- 2. Xenon Arc), 7. 20 hours exposure with no loss in tensile strength and greater than 7. Caution: “Sure- Seal. However, if a Sure- Seal. Thus, we recommend that both the plug and receptacle be replaced if environmental sealing is required after remating.”.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
October 2016
Categories |